Additional information
| Color | Red, White |
|---|
Magnum System 60 & 100 Heater Wrap (Set of 2)
$1,557.70
For use with the System 60 & 100 refillable foam kits. Fits a 420# cylinder.
Size: 53″ x 104″each
120V, 960 Watts, 8.0 Amps
Weight: 18lbs each
Sold in set of 2 wraps
Note: This wrap does not come with a hood for the top of the cylinder. Hoods may be purchased separately under item # HW-005.
Due to size, this item must be shipped via semi. Signature required at time of delivery. Due to expense, call for freight estimate.
J&R Products offers FREE SHIPPING for all domestic orders that total over $50 and are shipping to the lower 48 states. If you are needing items shipped outside of this area, please give us a call at 1-800-343-4446 to complete your order.
Additional information
You may also like…
Foam Box Warmer for up to 205 BF foam kits
Designed for warming up to 205 BF disposable spray foam kits, hoses, guns,and tools. Keep temperature sensitive materials safe from harsh winter weather and keep construction crews working all season long. This warming box also doubles as a hot box for caulking, glues, paints, and other temperature sensitive materials.
Specs:
Size- 16" x 16" x 16"
Temp - 70-80 degree F
Weight - 13 pounds
Min allowable temp for guaranteed results, -40 degrees
Voltage 120 volts
Power 280 watts
Current 2.33 amps
ETL Certified to UL/CSA Standards
55 Gallon Drum Heater Wrap with Thermostat Control (Set of 2)
For use with the 55 gallon drum refillable foam kits. It is sized for a 55 gallon drum with a built in thermostat of 160 degrees. It comes with adjustable straps to ensure proper fit of larger or smaller 55 gallon barrels. The drum heaters come ready to use. Unroll, wrap around your barrel, and plug into any outlet. The blankets weigh only 13 pounds and wrap around the entire barrel. This produces a fast, even, consistent heat. The built in thermostat will ensure you don't over/under heat your material. Each blanket has a 6 ft male end cord allowing five of these blankets to be plugged together on one single 20 amp outlet. Min allowable temp for guaranteed results is -40 degrees F with adjustable thermostat controller w/ heat probe.
120 volts/960 watt/8.0 amp (5 blanket maximum per 20 amp plug)
ETL Certified to UL/CSA Standards
Set of 2 Wraps
Foam Box Warmer for up to 605 BF foam kits
Designed for warming up to 605 BF disposable spray foam cylinder, hoses, guns,and tools. Keep temperature sensitive materials safe from harsh winter weather and keep construction crews working all season long. This warming box also doubles as a hot box for caulking, glues, paints, and other temperature sensitive materials.
Wraps are sold individually.
Note: 2 wraps are needed to warm both cylinders in a 2 part 600+ BF foam kit.
Specs:
Size- 13" x 13" x 23"
Temp - 70-80 degree F
Weight - 10 pounds
Min allowable temp for guaranteed results, -40 degrees
Voltage 120 volts
Power 280 watts, 2.33 amps
ETL Certified to UL/CSA Standards
Related products
Gallon Anchor Adhesive
Anchor adhesive is a high strength, heavy-bodied adhesive, specifically formulated for adhering anchors for hanging insulation. Anchor adhesive bonds metal and nylon anchors to metal, concrete or masonry surfaces. Can also be used to install metal or ceramic wall fixtures in tile applications. Anchor adhesive is also recommended for use as a general-purpose construction adhesive in applications requiring a high strength bond, or in applications subjected to high temperatures. Apply at room temperature and allow one day to dry before hanging insulation. One gallon adhesive used for 750-1000 anchors. SDS
Tenmat FF109-300 2-hour Fire Rated Light Cover
The FF109X is the only two hour UL tested and approved fire barrier that can be used with a wide range of recessed lights to effectively prevent the spread of flames through a ceiling opening. Once a hole is made in the drywall to install recessed lights or speakers, the integrity of the construction and its ability to perform in a fire is reduced significantly, creating a potential fire hazard. This is the reason why the International Building Code states: “Where floor/ceiling assemblies are required to have a 1 or 2-hour fire resistance rating, recessed fixtures shall be installed such that the required fire resistance of the ceiling will not be reduced” The FF109X is two hour approved for every major ceiling assembly including gypsum, sheetrock, drywall, acoustical tiles and suspended ceilings with any joist spacing up to 24 inch on center. The enclosure is made out of an intumescent material which will be activated in case of a fire, stopping both, flame spread and heat transmission for two hours. Tenmat 2 Hour Fire Rated Light Covers are UL tested and approved for use with IC-rated recessed incandescent, fluorescent, LED light fixtures. TENMAT Fire Rated Light Covers can be used with most light manufacturer’s models and are suitable for new construction as well as remodel projects. In addition to its fire protection capabilities, the FF109X also exhibits excellent thermal and acoustical insulating properties to save energy and reduce noise. The flexible and lightweight nature of the covers makes installation quick and easy, reduces the stress put on the ceiling and significantly reduces labor costs compared to standard dry-walled box constructions. Data Sheet (PDF)
Tenmat Recessed Light Cover
The Tenmat FF130E Recessed Light Cover is made out of a fire safe material and was specifically designed to protect your light fixture from insulation in the attic and to stop unwanted air leakage through your recessed light. The FF130E has been fire and thermally tested in accordance with UL1598 and IEC 60598-1 and can be used with IC, as well as Non-IC rated recessed lights (See installation instructions for maximum lamp wattage and types). Most recessed lights are not compatible with insulation and oftentimes start cycling on/off after they have been buried with cellulose, foam, fiberglass, etc. The lights' malfunction is a concern and a safety hazard. Pushing the insulation away is not an effective solution since it creates air passages in the building envelope and wastes energy. According to the department of energy, recessed lights account for 50% of the total thermal losses of a ceiling. Tenmat, the leading manufacturer of high-temperature engineering materials and fire protection components for recessed lights specifically developed the FF130E Recessed Light Cover to solve this problem and protect lights from insulation while simultaneously allowing the insulation to be continuous and uninterrupted over the whole area of the ceiling. Due to this improved air tightness and insulation, Tenmat users experience significant energy savings, noise reduction, and draft reduction. The FF130E covers are fit within seconds and do not require any assembly or special tools.
- Thermally tested according to UL 1598 for usage with IC and non-IC rated lights
- Fire tested in accordance with IEC 60598-1
- Saves energy by eliminating draft through your recessed light fixture
- Keeps flammable insulation at a safe distance from hot recessed lights
- Easy to fit - no assembly required
Ives Sash Lock
Brass plated window lock operates by cam action to eliminate rattles and hold windows firmly in place. Used singularly on small windows or in pairs for large windows. Complete with screws.